Drivers asrock p4vm800 windows xp11/4/2022 ![]() ![]()
![]() It is stable and quite well performing, if only somewhat hotter than how it performs on original speeds, though not worryingly so.Īnyway, lucky me the FX 5200 in question has an active cooler, and is not one of those passive cards Palit did a good job with the thermal solution on it, and I guess me cleaning it up thoroughly using fresh and quite good thermal grease also helped a bit. You were right, that was the issue after all with the GPU.Īlso did a quite promising overclock on the FX 5200, bringing it up to FX 5200 Ultra core clock and memory speeds (325 MHz and 325 MHz also, respectively). #Drivers asrock p4vm800 windows xp driverDeactivated that and booted into Windows and installed a fresh 175.16 driver for the FX 5200. #Drivers asrock p4vm800 windows xp proI flashed the BIOS on the K7VT4A Pro to the 1.80 version and unlocked the sidebanding option in the bios. I tinkered with the card and the motherboard a bit and finally set it all straight. #Drivers asrock p4vm800 windows xp driversThe drivers themselves were all downloaded from the Nvidia website, so I trust them to be legit, and not have injected malware in them that could explain the insane CPU usage.Īlso, no net connection on my retro-PCs, they are just intended for being retro gaming machines and just that.Īny advice? (except for throwing that trash of a card to the scrapheap, in general, I'm kidding, I'll probably just stick with 81.93 for now, if there are no other solutions to this problem) When I run it on the newer drivers results are abysmal because of the CPU usage. 3Dmark2001 SE scored ~5100 points on the Sempron and ~6700 points on the P4. What the hell is going on? Is the GPU faulty? Because, in all honesty it gets decent (I mean within the range) benchmarks when I run it on 81.98. #Drivers asrock p4vm800 windows xp PcMind you, this PC I put this FX 5200 inside was tested and over-tested with all sorts of hardware and I am 100% certain that there is no problem with it, nor with the drivers I have on it except apparently for those GPU Forceware ones. Same results, albeit this time only one single thread gets pegged up to 100% at a time (basically 50% CPU usage, as the other thread idles at 0-1%). #Drivers asrock p4vm800 windows xp installSpecifically a Prescott P4 3.4 GHz on a AsRock P4VM800, with a beefy 750 Watt power supply, fresh install of Windows XP SP3. Ok, so I thought to try it out on a better rig with a beefier CPU, see what happens then, as I figured the Sempron 2400+ isn't quite a powerhouse.ĭifferent motherboard, different CPU, more RAM (2 gigs, compared to the 512 the salvaged system had, DDR, both). CPU usage went down to idling at a normal 1-3%. Again, no artefacts, no crashes, nothing, clean install, clean reboot and 80% CPU usage. Ok, I uninstalled that driver and reinstalled it again same issue. ![]() Well, it did install, and it works, but for whatever reason it pegged the CPU down to 100% usage all the time after that (basically idling at 100%). All went fine there too, until I tried to install Forceware 175.16 for the GPU. Installed it in a new case, new PS, fresh install of win XP SP3 on a new HDD, everything seemed fine. Well the power supply definitely was busted (and beyond my ability to do anything about it, I am no electrical engineer, just a retro gaming hobbyist), but beyond that, the components seemed to be ok, even all the capacitors which I actually took the time to check individually, both visually and with my multimeter. Basic K7VT4A Pro board with an Sempron 2400+ and the dreaded FX 5200.Īnyway, it was due to be sent to the scrap bin, as it was deemed broken. So, recently I have been tinkering around with a old PC that I salvaged from my place of work. ![]()
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |